[BlueOnyx:23814] Re: After manual install of 5210R can't access server

f.kaegi at fairtalk.com f.kaegi at fairtalk.com
Sun May 3 04:24:58 -05 2020


Thanks Michael

I did what you suggested and all looks good.

1) Before that, I noticed that ETH0 has no link connected, it seems the
cable is connected to ETH2. 

I then configured ETH2 with onboot=yes and assigned the IP addresses to
broadcast, network, netmask, ipaddr, and dns0. 

Now I can log in to the GUI and it brings me to the BlueOnyx 5210R
Setup-Wizard. 
Here, in the system settings it shows for the Primary Interface the MAC
address of ETH0 (no IP addresses), for the Third Interface the correct IP
addresses, but no MAC Address. 
When I finish the Setup-Wizzard I get the error:

An uncaught Exception was encountered
Type: Error
Message: Call to undefined function find_free_device()
Filename:
/usr/sausalito/ui/chorizo/ci/application/modules/base/wizard/controllers/Wiz
ard.php
Line Number: 516

Looking at line 516 in Wizard.php I see "$new_device =
find_free_device($CI->cceClient, 'eth0');"

Does it matter to which port the Ethernet cable is connected? Should I ask
the housing provider to connect the cable to ETH0?
Or how else can I solve this issue?

2) May I ask you another question?
Presently my old 5208R box is running with 5 IP addresses. 
I will now use Easy Migrate to migrate all relevant content to this new
5210R box.
Then the housing provider will assign my "old" IP addresses to the new
server.
How can I avoid that user content, particularly emails, that are still
coming in to the old server are not lost forever during the time the housing
provider requires to switch the IP addresses from the old to the new server?

Thank you for your kind attention and support.
All the best
Felix

-----Original Message-----
From: Blueonyx <blueonyx-bounces at mail.blueonyx.it> On Behalf Of Michael
Stauber
Sent: Sunday, 3 May 2020 03:29
To: blueonyx at mail.blueonyx.it
Subject: [BlueOnyx:23813] Re: After manual install of 5210R can't access
server

Hi Felix,

> I got a new server running CentOS 8 and manually installed 5210R 
> following step-by-step the guidelines on 
> https://www.blueonyx.it/5210r-manual-install.
> 
> At the end of the process it showed how and where to reach the GUI 
> interface. However, when I enter xxx.xxx.xxx.xxx:81/login I get the
> error: This site can’t be reached xxx.xxx.xxx.xxx took too long to
respond.
> 
> I have SSH access to the server via a remote maintenance interface. 
> How can I troubleshoot the problem?

Login by SSH as "admin" (password should be "blueonyx") and "su -" to become
root.

If that doesn't work, try to login as "root" with either the password
"blueonyx" *or* whatever the password was before.

Check the running processes. See if "admserv" is running. You can also check
that with "systemctl status admserv".

Possibly there are still initial setup tasks running, which can take several
minutes. You can check that by running "tail -f /var/log/messages" and see
if there are frequent CCEd messages other than the ones from "Active
Monitor".

Check if firewalld is disabled:

systemctl status firewalld

If it is, you might want to stop and disable it:

systemctl stop firewalld
systemctl disable firewalld

Once all setup tasks are done and firewalld is disabled, AdmServ should be
reachable.

--
With best regards

Michael Stauber
_______________________________________________
Blueonyx mailing list
Blueonyx at mail.blueonyx.it
http://mail.blueonyx.it/mailman/listinfo/blueonyx




More information about the Blueonyx mailing list