[BlueOnyx:13732] Re: old raq550 question
webmaster
webmaster at oldcabin.net
Tue Sep 24 12:12:44 -05 2013
had to install smartctl before I could run these
Below are snips from running "smartctl -a /dev/hda" and then
"smartctl -a /dev/hdc"
Anyone see anything indicating a bad drive?
[root smartmontools-5.32]# ./smartctl -a /dev/hda
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST380021A
Serial Number: 3HV4PLF1
Firmware Version: 3.19
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Sep 24 12:09:29 2013 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 422) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 57) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 070 034 Pre-fail
Always - 130575369
3 Spin_Up_Time 0x0003 070 070 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 2
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 5
7 Seek_Error_Rate 0x000f 086 060 030 Pre-fail
Always - 434973384
9 Power_On_Hours 0x0032 008 008 000 Old_age
Always - 81257
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 135
194 Temperature_Celsius 0x0022 030 049 000 Old_age
Always - 30
195 Hardware_ECC_Recovered 0x001a 080 070 000 Old_age
Always - 130575369
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age
Always - 0
SMART Error Log Version: 1
ATA Error Count: 46 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 46 occurred at disk power-on lifetime: 15719 hours (654 days + 23
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 4d 43 f0 b9 e0 Error: UNC 77 sectors at LBA = 0x00b9f043 =
12185667
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 10 f0 b9 e0 00 06:10:53.611 READ DMA
c8 00 80 90 ef b9 e0 00 06:10:53.578 READ DMA
c8 00 80 10 ef b9 e0 00 06:10:53.569 READ DMA
c8 00 80 90 ee b9 e0 00 06:10:53.561 READ DMA
c8 00 80 10 ee b9 e0 00 06:10:53.553 READ DMA
Error 45 occurred at disk power-on lifetime: 15716 hours (654 days + 20
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 4d 43 f0 b9 e0 Error: UNC 77 sectors at LBA = 0x00b9f043 =
12185667
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 10 f0 b9 e0 00 03:26:14.529 READ DMA
c8 00 80 90 ef b9 e0 00 03:26:14.501 READ DMA
c8 00 80 10 ef b9 e0 00 03:26:14.493 READ DMA
c8 00 80 90 ee b9 e0 00 03:26:14.484 READ DMA
c8 00 80 10 ee b9 e0 00 03:26:14.476 READ DMA
Error 44 occurred at disk power-on lifetime: 15715 hours (654 days + 19
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 4d 43 f0 b9 e0 Error: UNC 77 sectors at LBA = 0x00b9f043 =
12185667
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 10 f0 b9 e0 00 00:36:30.173 READ DMA
c8 00 80 90 ef b9 e0 00 00:36:30.142 READ DMA
c8 00 80 10 ef b9 e0 00 00:36:30.134 READ DMA
c8 00 80 90 ee b9 e0 00 00:36:30.126 READ DMA
c8 00 80 10 ee b9 e0 00 00:36:30.118 READ DMA
Error 43 occurred at disk power-on lifetime: 15712 hours (654 days + 16
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 4d 43 f0 b9 e0 Error: UNC 77 sectors at LBA = 0x00b9f043 =
12185667
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 10 f0 b9 e0 00 11:20:46.090 READ DMA
c8 00 80 90 ef b9 e0 00 11:20:46.058 READ DMA
c8 00 80 10 ef b9 e0 00 11:20:46.050 READ DMA
c8 00 80 90 ee b9 e0 00 11:20:46.042 READ DMA
c8 00 80 10 ee b9 e0 00 11:20:46.034 READ DMA
Error 42 occurred at disk power-on lifetime: 15709 hours (654 days + 13
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 4d 43 f0 b9 e0 Error: UNC 77 sectors at LBA = 0x00b9f043 =
12185667
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 10 f0 b9 e0 00 08:30:44.510 READ DMA
c8 00 80 90 ef b9 e0 00 08:30:44.477 READ DMA
c8 00 80 10 ef b9 e0 00 08:30:44.469 READ DMA
c8 00 80 90 ee b9 e0 00 08:30:44.461 READ DMA
c8 00 80 10 ee b9 e0 00 08:30:44.453 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
######################################################################
[root smartmontools-5.32]# ./smartctl -a /dev/hdc
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST380021A
Serial Number: 3HV4PDGT
Firmware Version: 3.19
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Sep 24 12:10:11 2013 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 422) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 57) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 075 072 034 Pre-fail
Always - 143743403
3 Spin_Up_Time 0x0003 070 070 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 2
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 086 060 030 Pre-fail
Always - 403284815
9 Power_On_Hours 0x0032 008 008 000 Old_age
Always - 81240
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 135
194 Temperature_Celsius 0x0022 030 050 000 Old_age
Always - 30
195 Hardware_ECC_Recovered 0x001a 075 072 000 Old_age
Always - 143743403
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
More information about the Blueonyx
mailing list